Dual Link com Bounding

Artigo do site: http://www.debianhelp.co.uk/bonding.htm

What is Ethernet Bonding ?

Ethernet bonding refers to aggregating multiple ethernet channels together to form a single channel. This is primarily used for redundancy in ethernet paths or for load balancing. This page refers in particular to performing ethernet bonding under linux, and so does not limit itself to discussion of 802.3ad Trunk Aggregation.

Bonding Types

The linux kernel bonding module supports a number of bonding types.

Round Robin

Packets are transmitted in a round robin fashion over the available slave interfaces. Provides both load balancing and fault tolerance

Active Backup

One slave interface is active at any time. If one interface fails, another interface takes over the MAC address and becomes the active interface. Provides fault tolerance only. Doesn’t require special switch support

Balance XOR

Tranmissions are balanced across the slave interfaces based on ((source MAC) XOR (dest MAC)) modula slave count. The same slave is selected for each destination MAC. Provides load balancing and fault tolerance.

Broadcast

Transmits everything on all slave interfaces. Provides fault tolerance.

802.3ad

This is classic IEEE 802.3ad Dynamic link aggregation. This requires 802.3ad support in the switch and driver support for retrieving the speed and duplex of each slave.

Balance TLB

Adaptive Transmit Load Balancing. Incoming traffic is received on the active slave only, outgoing traffic is distributed according to the current load on each slave. Doesn’t require special switch support

Balance ALB

Adaptive Load Balancing – provides both transmit load balancing (TLB) and receive load balancing for IPv4 via ARP negotiation. Doesn’t require special switch support, but does require the ability to change the MAC address of a device while it is open

Setup Bonding Ethernet on Debian with a 2.4 kernel

To use Bonding Ethernet for High-Availability (fail-over) on Debian (Woody, Sarge or Sid with a 2.4.x kernel) you need to:

install package ifenslave-2.4.To install this package follow this command

#apt-get install ifenslave-2.4

make sure the real NICs kernel modules are loaded automatically

edit /etc/network/interfaces to look like this:

iface bond0 inet static
address 10.31.1.5
netmask 255.255.255.0
network 10.31.1.0
gateway 10.31.1.254
up /sbin/ifenslave bond0 eth0
up /sbin/ifenslave bond0 eth1

comment or borrow the lines referring to your real NICs in the same file

add the following lines to your /etc/modutils/arch/i386:

alias bond0 bonding

options bonding mode=1 miimon=100 downdelay=200 updelay=200

Now run the following command for update

#update-modules

Setup Bonding Ethernet on Debian with a 2.6 kernel

To use Bonding Ethernet for High-Availability (fail-over) on Debian (Woody, Sarge or Sid with a 2.4.x kernel) you need to:

install package ifenslave-2.6.To install this package follow this command

#apt-get install ifenslave-2.6

make sure the real NICs kernel modules are loaded automatically

edit /etc/network/interfaces to look like this:

iface bond0 inet static
address 10.31.1.5
netmask 255.255.255.0
network 10.31.1.0
gateway 10.31.1.254
up /sbin/ifenslave bond0 eth0
up /sbin/ifenslave bond0 eth1

comment or borrow the lines referring to your real NICs in the same file

add the following lines to your /etc/modprobe.d/arch/i386:

alias bond0 bonding

options bonding mode=1 miimon=100 downdelay=200 updelay=200

About fcacomputers

Just du it
This entry was posted in LINUX. Bookmark the permalink.

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s